How to create a firmware dump


Rendering Error in layout Widget/Social: Call to a member function exists() on null. Please enable debug mode for more information.
More
8 years 10 months ago #515 by bkesm605
I have a SP8-B programmer that uses Flypro software and I'm not sure how to create a dump. Please advise and thanks in advance.

Please Log in or Create an account to join the conversation.

More
8 years 10 months ago #518 by codefiend
check out thaGHO5T's new tutorial uploaded, he shows you how to make a dump.

Please Log in or Create an account to join the conversation.

More
8 years 10 months ago #520 by thaGH05T
Please explain your situation. I need to know what Mac you have as well. Why did you decide to go with that programmer?

Please Log in or Create an account to join the conversation.

More
8 years 10 months ago #522 by bkesm605
Long story short I bought a macbook pro from a shady dude and it was firmware locked (didn't know at the time of sale) and it has no OS on it so I get flashing folder sign or firmware password icons. So going from the serial on the back "ultimate mac lookup website" says its a MacBook Pro "Core i5" 2.5 13" Mid-2012 EMC *2554. I've taken out hard drive and tried formatting on another mac I have....didn't work says it has bad last block. Tried a new hard drive with OS on it...didn't work. I got the controller off ebay for 10$. I'll be more than happy to give my dump once I figure that out. Please advise and thank you it is very much appreciated.

Please Log in or Create an account to join the conversation.

More
8 years 10 months ago #523 by thaGH05T
Ok Can you please post pics of your setup? I need to see all the tools you have available. Do you have just the programmer and USB cable? Or did it come with an SOIC8 clip as well? I am sure this can be used, but I have to get it figured out.

Please Log in or Create an account to join the conversation.

More
8 years 10 months ago #524 by bkesm605
The controller is then connected via USB to my computer and it uses Flypro software.

Please Log in or Create an account to join the conversation.

More
8 years 10 months ago #525 by bkesm605







The controller is then connected via USB to my computer and it uses Flypro software.
Attachments:

Please Log in or Create an account to join the conversation.

More
8 years 10 months ago #526 by thaGH05T
If you have it hooked up right you can then use flyPro to read the ROM and back it up. And then you can choose a file to write back to it, which I have your EMC in the repository I do believe. The software is simple to navigate and self explanatory if I remember correctly. It should be on the left hand pane, one click of a button.

Please Log in or Create an account to join the conversation.

More
8 years 10 months ago #527 by bkesm605

Does this look correct? The first pin is uncovered and 2nd has to be red for vvc on flypro. When I connect it to pc I choose the device type and when I start it says device ID doesn't match but I proceed anyways and when I read it comes up empty so I write (program) chip it says successful, then when I read again it comes up empty and verify fails. Any ideas?
Attachments:

Please Log in or Create an account to join the conversation.

More
8 years 10 months ago #528 by thaGH05T
The pinout of your programmer has certain color wires for each. So just connect the correct wires to the correct pin. I have many pictures of the chips pinout. And I hope the write didn't succeed because you can brick your Mac. Do you understand the process of flashing eeprom? What did u think you were flashing back?

Please Log in or Create an account to join the conversation.

Who's Online

We have 849 guests and no members online

N00BZ

  • ljamal
  • ljamal74
  • mikeg2atest
  • ducchinhbui
  • anjarezt

Cookies